Prescolite LD6_S Instrukcja Użytkownika Pobierz pdf

InstructionSheet

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93011925

InstructionSheet

INSTALLATION INSTRUCTIONS

LD6_S SERIES

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

FIG. 1

FIG. 2

NOTE: Do not pinch LED wires between the sliding parts.

KEEP THESE INSTRUCTIONS

Canopy

Outlet Box

Mounting Screws

Screws #8-32

(2)

Mounting Plate

Light Engine

Mounting Screw

Trim

Driver

Mounting Screws

Driver Bracket

Mounting Screws

Light Engine

Connector

Driver

Mounting Screws

Connector

Driver Bracket

Mounting Screws

Driver Bracket

Light Engine

Mounting Screw

Light Engine

Trim

Driver

Mounting Screws

Connector

Driver Bracket

Mounting Screws

Driver Bracket

Light Engine

Mounting Screw

Light Engine

Safety Cable

Trim

Safety Cable

anopy

Outlet Box

Mounting Screws

Screws #8-32

(2)

Mounting Plate

Light Engine

Mounting Screw

Trim

Driver

Mounting Screws

Driver Bracket

Mounting Screws

Light Engine

Connector

Driver

ounting Screws

Connector

Driver Bracket

Mounting Screws

Driver Bracket

Light Engine

Mounting Screw

Light Engine

Trim

Driver

Mounting Screws

Connector

Driver Bracket

Mounting Screws

Driver Bracket

Light Engine

Mounting Screw

Light Engine

Safety Cable

Trim

Safety Cable

701 Millennium Boulevard • Greenville, SC 29607

ith representatives of

fices in principal cities throughout North

America.

CEILING MOUNT

etach mounting plate from cylinder canopy by loosening the two #8-32

crews that hold the strap in the canopy (Fig.1).

2. Make electrical connections. Connect ground wires to green ground leads.

onnect power supply (line) to black leads

WARNING: DO NOT pinch wires. Consult a qualified electrician for all

other options that require other wiring configurations.

ecure mounting plate to outlet box with screws from outlet box (Fig.1).

4. Secure the fixture in place by tightening the screws from step 1.

NSTALLATION

nsert supplied #8-32 x 1/2” screws into supplied S-4 strap through tapped

oles located 2-3/4” apart in orienation shown in Fig 1. (Holes in fixture

canopy must line up with these screws.)

ount strap to outlet box with screws (by others) with screw stems facing

outward. Rotate strap to adjust fixture to correct position.

3. Connect supply wires: Black to Line, White to Common, Green to Ground.

(DM only: Connect Gray (+) and Violet (-) to appropriate 0-10V dimming

control per National Electrical Code and local codes.

4. Secure fixture canopy with two mounting nuts supplied.

5. Fixtures used in wet locations, place the two supplied o-rings under the

heads of the mounting screws and secure mounting nuts. Area around fix-

ture canopy and mounting surface must be sealed.

LIGHT ENGINE REPLACEMENT

Remove lensed reflector assembly by pulling from the edges. Reflector

assembly is held by a safety cable.

2. Loosen captive screw holding the light engine. Carefully lower and discon-

nect light engine connector from driver connector. See Fig. 2.

3. Connect replacement light engine connector to driver connector and line up

light engine heat sink fins with mounting bracket until seated into place and

tighten captive screw.

4. Reinstall reflector assembly.

LED DRIVER REPLACEMENT

Remove lensed reflector assembly by pulling from the edges. Reflector

assembly is held by a safety cable.

2. Loosen captive screw holding the light engine. Carefully lower and discon-

nect light engine connector from driver connector. See Fig. 2. Set aside.

3. Remove driver bracket mounting screw attaching safety cable and remove

reflector assembly. Set aside.

4. Remove remaining driver bracket mounting screws and lower driver brack-

et. Disconnect all driver wiring and replace driver by removing driver

mounting screws. See Fig 2.

5. Mount replacement driver and reconnect wiring according to installation

step 3.

6. Reinstall driver bracket and safety cable holding reflector assembly using

mounting screws. Reconnect light engine connector to driver connector

and line up light engine heat sink fins with mounting bracket until seated

into place and install with captive screw.

7. Reinstall reflector assembly.

InstructionSheet 1

Podsumowanie treści

Strona 1 - InstructionSheet

InstructionSheetwww.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ETPart No. . . . . . . . . .

Komentarze do niniejszej Instrukcji

Brak uwag

Prescolite LD6_S Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oświetlenie Prescolite LD6_S. Prescolite LD6_S User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oświetlenie Prescolite LD6_S